Hard Top Boat Covers
You can now cover your entire hard top boat. WE'VE GOT YOU COVERED!!!!!!!!!
Please call us to order 10.00m x 5.50m or 10.50m x 5.78m Hard Top covers. They are in stock ($599) in Navy and in Black but we have a glich on the site at the moment for this product size.
Due to the top quality cut these are best suited to Hard Top Boats with outboard motors. You may need some local adjsutment if you do not have an outboard.
These hard top covers do not generally sit well on Boats with a normal soft Bimini Top. Do look at our Bimini Top Boat Cover pages for extra wide covers.
We offer you our SUPERIOR QUALITY "OCEAN PRIDE" MATERIAL COVER with a FIVE YEAR GUARANTEE in Light Navy Blue or Black which enable you to cover entirely hard top cabin and rocket launchers.
From just $550.00 Our covers will suit hard top boats from 5.5m long to around 10m long. Our covers are re-enforced on the entire full roof-top area, the outboard motor, the two rear corners and at the bow. In fact about 80% of the cover is re-enforced. As well as straps to tie down to the trailer bars there is a STRONG cord around the hem to pull the cover nice and snugly around the boat.
When comparing prices elsewhere ask if they give you a FIVE YEAR GURANTEE if not then you do not need to ask why because we honour our guarantee. Wait and hear them tell you why they will not give you that guarantee and then why you should not buy our covers. I can tell you some stories believe me!
Our superior quality covers come with a genuine FIVE YEAR GUARANTEE against significant fading and material deterioration.
"Why pay a lot more elsewhere without receiving a FIVE YEAR GUARANTEE?"
Our quality and prices has forced one of our competitors to take almost $100 off their prices but they still do not match our quality OCEAN PRIDE covers nor do they offer you a 5 year guarantee as we do.
ALL covers are 100% waterproof and have a soft breathable inner liner (Not PVC which breaks up quickly).
Double Buckles are supplied liberally around the cover sides, bow and stern to fit to your trailer bars or under and over your boat if you wish. Strong ROPE bungee cord around hem.
We do not cover tearing of material as sadly some customers do not take the care they should when attaching and removing covers. We do not cover rubbing damage so protect as you feel necessary.
MEASURING YOUR BOAT: Please Measure carefully
As a General guideline Hard Top boats with a STRAIGHT hull length of
up to 6.00m will probably require the 8.65m cover.
6.00m - 7.00m probably either the 9.25m or 10.00m cover
Over 7.00m probably the 10.50m cover
However we advise you to measure your own boat before making a purchase. Rocket Launchers could change this.
We have a guide chart so can help you if you give us the make and model of your boat.
Length: Take a tape from the bow (near your winch) to the stern along the centre line and OVER the highest point of the hard top or Bimini (This may be the rocket launchers if you have them fitted. Include anchor if fitted and outboard motor if you have one and wish to cover it. We suggest down to the bottom of the cowling cover.
Width: From at least the gunwhale (Rubbing strip) on one side to the same point on the other side over your boat OVER the HIGHEST point of your boat. We advise that you should start from below the rubline (gunwhale) on each side depending on how much of your boat you require covered, you can come down to the bottom of the hull if you wish. Match your measurements with the nearest size of material shown below.
Please note: we do not accept any responsibility for tearing as sadly not every customer takes as much care as they should when using covers. We are not experts to say how tears occur. It is YOUR responsibility to protect all sharp points as we will take no responsibility for tears or rubbing damage. These covers are cut for HARD TOP shape and you will need our extra wide Bimini top covers for putting on boats when you leave the Bimini up!
|